zmena IDE na AHCI (win 10 )

Dobry den prajem , potreboval by som poradit(noob)
mam 1 ssd(corsair force 3 240gb)-systemovy(win 10 ,v1607) a 2 hdd datove (seagate ST1000DM003 1TB 64MB Cache SATA 6.0Gb/s) potreboval by som ich z IDE modu hodit do AHCI bez toho aby som nieco preinstalovaval, je to mozne??
doska je GA-Z68AP-D3 (rev. 2.0) - sata 3 porty oznacene - 0,1 // sata 2 - 2,3,4
v biose je moznost prepnut pre porty 0-3 jednotlivo ide,raid,ahci , chcel som povodne aspon ssd prehodit do ahci s tym ze hdd dam do portu 4 ale zvysny by som musel dat do portu 3 a ten by bol ahci

dakujem za rady

reedit - skusil som dat safeboot , v biose som prehodil ide na ahci ale nebootlo mi do do safemode, vyhodilo mi blue screen, tak som to prehodil spat na ide

siel som podobne ako v tom navode len podla tohoto kedze toto je pre win 10

1. While in Windows, press the Win+R keys to open Run, type regedit, and click/tap on OK to open Registry Editor.
2. If prompted by UAC, click/tap on Yes.
3. In the left pane of Registry Editor, browse to the key location below.


HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV
4. In the right pane of the iaStorV key, double click/tap on the Start DWORD to modify it. (see screenshot above)
5. Type 0 (zero) for AHCI, and click/tap on OK.

6. In the left pane of Registry Editor, browse to the key location below.


HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorAV\StartOverride
7. In the right pane of the StartOverride key, double click/tap on the 0 DWORD to modify it.
8. Type 0 (zero), and click/tap on OK.

9. In the left pane of Registry Editor, browse to the key location below.

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci

10. In the right pane of the storahci key, double click/tap on the Start DWORD to modify it. (see screenshot above)
11. Type 0 (zero) for AHCI, and click/tap on OK.

12. In the left pane of Registry Editor, browse to the key location below to see if you have the StartOverride here. If you don't, then go to step 15 below.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci\StartOverride

13. If you do, then, in the right pane of the StartOverride key, double click/tap on the 0 DWORD to modify it.
14. Type 0 (zero), and click/tap on OK.

15. When finished, close Registry Editor.
16. Boot the computer to your BIOS or UEFI firmware settings.

17. In your BIOS or UEFI firmware settings, enable AHCI, and save & exit to apply and restart the computer.

Note: These settings will vary per brand and model number of motherboard. Please read your motherboard manual for more specific details about how to change SATA settings for it.

18. When Windows starts, it'll automatically install AHCI drivers.

19. When finished, you'll need to click/tap on Restart Now to restart the computer one last time.

Check if it helps. For further assistance you can contact Samsung support.

Thank you.

// Spojený príspevok Štv 31.05.18 18:46

po tomto navode doslo k zmene na ahci ale po spusteni windowsu mi
hodnoty iaStorV a iaStorAV zmenilo naspat na hodnoty 3 a vsetky disky mi teraz zobrazuje ako odnimatelne media

// Spojený príspevok Štv 31.05.18 19:48

nenasiel som vhodne ahci/raid ovladace neviem co ma znamenat to zobrazovanie diskov ako removable , nemoze dojst k poskodeniu diskov??

https://support.microsoft.com/en-us/help/3083627/internal-sata-drives-show-up-as-removeable-media

To čo si robil vráť späť a nastav si to takto:
HKEY_LOCAL_MACHINE-System-CurrentControlSet-Services-Storahci - Nastav hodnotu Start na 0.
HKEY_LOCAL_MACHINE-System-CurrentControlSet-Services-pciide - Nastav hodnotu Start na 0.